Monday, June 29, 2009

Central Vacuum Systems For Your Home

What is a central vacuum system? A central vacuum system is made up of a group of inlets that are connected via piping to an integral power and canister unit. The inlets are generally wall mounted, but can also be floor mounted. Each inlet allows you to vacuum 700 to 800 square feet. A flexible hose, approximately 30 feet long plugs into the outlets. Numerous types of suction heads are available to connect to the end of the hose, including power beaters.

The power/canister unit is usually mounted in a garage or basement.

Most handymen can install a central vacuum system, without the need for professional assistance. The most complex part of the installation is physically running the two inch plastic piping from the power unit to the inlets.

There are many reasons to consider the installation of a central vacuum system for your home:


  • Relieves Allergy Symptoms: As the power unit and canister are mounted outside of the living area of the home, exhaust air from the vacuum is not circulated back into the room being vacuumed which substantially improves the air quality in the room. Coupled with good filtration, many manufacturers are using HEPA filtration, almost 100% of the contacted dirt, dust mites, pollen, dander, and other allergens are removed and contained.
  • More Power: Central vacuum systems deliver up to five times more suction power than conventional upright or canister vacuum cleaners. More suction equates to better overall cleaning.
  • Larger Canister: The canister that is attached to the power unit holds as much as six gallons of dirt, 10 times more dirt than conventional upright or canister vacuum cleaners. You can vacuum longer without the inconvenience of changing bags or emptying canisters.
  • Convenience: Have you ever tried to vacuum a ceiling fan, drapes, blinds? Usually the hose is not long enough, even with the extension pipes you end up lifting the vacuum cleaner in the air in order to reach the corners and tops. With the long hose associated with a central vacuum system, reaching corners, ceilings, and other difficult areas is easy.

    Have a multi-story home? Then you have faced the inconvenience of carrying your vacuum cleaner up and down stairs, not to mention the difficulty in actually vacuuming stair cases, usually it means trying to position the vacuum on the steps in order to reach all points.

  • Quiet Because the power unit is not in the living area of the home, there is far less ambient noise when vacuuming. You can hear the phone ring, listen to music and answer the front door.

If you are looking for a home improvement project that will be of benefit to the entire family consider a central vacuum system. As with any home appliance, it is wise to investigate the specifications, features, and accessories available before you choose the manufacturer and model that suits your requirements best.

Renovation-Headquarters has additional information on the installation of a central vacuum system in your home.

For additional information on home improvement, remodel or other renovation projects, including landscaping and gardening, visit Renovation Headquarters.

Roof Repairs

Looking For a UPVC Windows Company?

It is essential for anyone thinking of replacing there windows to know which company will provide the best service. There are many quality UPVC specialists that can offer a professional service for persons looking for windows Cardiff, Newport and South Wales in general. However, it is still advised to research before you settle for a company for definite.

Many people are now choosing to have UPVC windows in their home because they are not only more resistant, they help reduce the loss of heat, easy to clean and long lasting. With doors available to match the windows to truly make your house look how you want it. Specialists in UPVC windows have the knowledge to be able to advise you on the type of windows and doors that would be best for your home. Knowing designs and colours that could suit your home, UPVC professionals are the best option to have to ensure you get what you pay for.

There are a wide variety of options open to anyone look to change to UPVC windows, but there are two distinct styles that are available form some UPVC specialists.

Ovolo - curved to the window frame edge

Chamfered - lines across the pane

These are two types of style and both give a different feel to a home but both as equally charming as each other. Choosing your windows is like choosing your dcor, you need the one which will reflect you and your home, but unlike the inside of your home, you windows will be admired by anyone that passes. Depending on what you have in mind, either of these will be suitable for any home and still give a classic, professional look from inside and out. However whatever the windows, a quality company will make sure this is the case.

Written by Jenny Pilley member of CReare Communications SEO specialists, on behalf of Peter Fennell of Windows Cardiff specialists

Insulation Blocking Attic Vents

Sunday, June 28, 2009

Backsplash For Bathroom Tile - Easy Remodeling Technique!

Backsplash For Bathroom Tile remodeling is a great option for home-makers to easily redecorate any surface at home. When it comes to contemporary and easy DIY tiles, using this unique tiling technique is an alternative you should consider. Want to learn how it can help you redecorate your home? Read the following article.

Quick introduction

Backsplash For Bathroom Tile redecoration is made of a set of identical beach-stones fixed onto a sq/ft mesh backing. We may find that these panels are made of stones originated from various beaches and rivers from all over the world - mostly from S. East Asia. This tiling technique enables you to easily redecorate anywhere in the inside & the outside: Bathroom flooring and wall coating (including showers), kitchen surfaces such as countertops & backsplashes, patios, pools and even fireplaces.

Important benefits

Let's quickly summarize the main advantages and benefits of this unique technique:

* Can be used for virtually unlimited applications at home, in the office, in restaurants, hotels, etc.
* Can be used for dry surfaces as well as wet surfaces such as shower flooring or as a sink backsplash.
* Their surfaces are flush and in fact, are safer to walk on than most conventional hard flooring as they offer more traction to prevent slipping.

Valuable tips to go!

* Use a tile saw in order to cut stones to fit edges or corners.
* Most recommended grout is sanded grout - it is suitable for both internal and external use.
* Don't rush! - make a plan; make sure you know how to install these panels, even make a small trial first just to see that you can handle it with no problem.

We could easily find many other great benefits provided by this simple redesigning method simply because it provides virtually unlimited remodeling options to any space and surface at any size and location whether for interior or exterior uses.

Quick summary

It is considered as one of the best tiling choices for the average home-maker due to the fact that Backsplash For Bathroom Tile can be quickly installed with minimal required technical skills, and at low cost. If you wish to succeed with your first installation it is recommended to keep the above tips before you begin with installation.

Get creative! - Learn more about how you can easily decorate any surface at home or in the office with Backsplash For Bathroom Tiles.

Visit: http://www.homepebbletiles.com

How to Create the Perfect Patio Experience

By taking time to plan and design your patio, you can create an area where all the different features combine to produce a unique space that possesses character, comfort and charm. In effect, transforming a popular garden feature into an outside room.

To create the perfect patio for your garden, consider the size and position of the patio area carefully. Most people prefer the patio to be close to the house but you may wish to choose a location in a sunnier part of the garden or a position offering a better view.

By placing the patio near to trees and shrubbery, you create a naturally sheltered area similar to an arbour. But this type of location can bring problems. Firstly excavating the footings for the patio may cause damage to the roots of the trees and shrubs that were the chief attraction of that particular location. Close proximity to trees and shrubs will almost definitely result in the unsightly problem of leaf mould forming on the patio creating a slippery and hazardous surface.

For a patio that complements the house and garden, proportions are all-important. When deciding on the size of the patio, you must also think practically about how it will be used. If you want to put a table and chairs on it, you will probably need at least 3m x 3m but to accommodate sunloungers and possibly barbeques a larger space may be required. So it's worthwhile deciding on the type of patio furniture you will be using at this early stage.

Shape is another important factor in your patio planning. Don't be constrained by the traditional rectangular template - a curved patio is often more space efficient and can blend more harmoniously with the rest of the garden. Experiment with shapes and geometric patterns to highlight garden features or mirror flowerbeds. Mark out the patio area with a hosepipe or string line to help you visualise the space.

Once you have decided on the shape and size of your patio there is another important feature of the design to consider that many people overlook - colour. The variety of stone available to the patio builder is matched, if not surpassed, by the rich diversity of colours in which stone paving materials now come. A quick glance at any paving stone supplier's catalogue or website will vividly illustrate this. We will look at the colours available later, but at this stage it is a good idea to consider whether you want the colour of the patio to complement or contrast with the colour of the walls of your house.

Then there are the questions of patterned or plain and mix or match? Are you going to use stone of the same colour or do want to create a pattern on the patio surface?

Matching different materials is yet another option worth considering. A patio constructed of two different types of stone can be very effective, as can the inclusion of an area of decorative gravel in the design. But if the mix and match approach appeals to you take care, for not all materials will work well together.

As with so much connected with design, personal taste plays a significant and overriding role. Nevertheless, it is a generally accepted rule that natural stone does not work well with reconstructed materials.

The patio's perimeter also offers the opportunity for other design elements that can enhance its overall appearance. Firstly, you may want to build a low ornamental wall around the perimeter of your patio. Once again it is at the design stage where you should be looking into the height of the wall, the type and colour of the brick you are going to use and whether the top of the wall will be finished with coping or incorporate areas for planting.

Another option worth considering is having contrasting edging at the patio's perimeter, which can be in terms of both colour and material. A patio constructed of slabs can be given an elegant block edging, providing a simple but effective counterpoint to the main patio area.

Whatever design you are looking for, it is advisable to produce scale drawings to visualise the finished patio. Scale drawings can also assist in calculating the quantity of materials needed.

Patio slabs

Stone slabs or flags come in many shapes, sizes and colours. The main types of stone are natural stone and reconstructed stone. Natural stone is what its name implies and is the more expensive of the two; but natural stone slabs can vary in size and thickness and consequently will require a higher degree of expertise to lay.

Reconstructed stone slabs - sometimes described as reconstituted or artificial stone - are concrete units where a specific concrete mix has been designed to resemble natural stone. A wide range of natural stones can be imitated including Bath stone, Portland stone, Stainton stone and red terracotta.

A word of caution on reconstructed stone slabs. Although they are the less expensive option, the quality can vary greatly and the cheapest stone slab often bears little resemblance to the natural stone it is trying to imitate. So it's advisable to look around to find the best supplier.

Traditionally the most popular stone for building patios has been sandstone, as it comes in a wide range of attractive colours and textures. But there are other interesting and decorative alternatives.

Travertine is a hardwearing stone common to southern Europe. The largest building in the world constructed predominently of travertine is the Colosseum in Rome. A noticable feature of travertine stone is its naturally pitted surface that is excellent for simple, rustic designs. But it's the colours of travertine stone that make it so attractive to patio builders. In addition to grey, beige and white there are rich browns, reds and golds that are ideal for creating a patio with a Mediterrannean appearance.

Another stone favoured by professional patio builders is granite. The reputation granite has for toughness and durability often overshadows its natural beauty. Natural granite slabs are usually dark and silver grey, or pink. But its beauty is heightened in the sun as it sparkles and glints providing a glamorous sophistication.

When looking at the variety of stone available you will soon discover that patio slabs can come with different finishes offering another dimension to patio design. These finishes are produced by specific operations: acid-etched, smooth or coarse ground, grit or sand-blasted, rubbed or polished, giving the stone a different appearance and character.

A riven surface refers to stone that has the appearance of having split away from the main rock mass resulting in a rough, textured appearance. Tumbled stone has a distressed look marked by rounded edges and a well-worn quality. Polished stone has a smooth surface imparting a refined elegance, while in stark contrast slabs that have been shot-blast have a coarse, roughened surface.

Block paving and setts?

Although the patio slab or flag is the most popular stone material for building patios other materials are available, namely block paving and setts.

Block paving comprises of rectangular shaped blocks similar to bricks. The most common size for block pavers is 200mm x 100mm with a depth of around between 50mm. They can either be made of concrete or clay and come in a wide selection of colours. Clay paving blocks are more expensive than the concrete variety but both can be tumbled or polished

Paving blocks are usually laid in one of three patterns: herringbone, stretcher bond and basketweave.

Whatever stone material you decide to use, accurate plans will help you estimate the quantity of materials needed and get quotes. Remember to check that there are no underground pipes and cables in the area. If the patio is to butt onto an exterior house wall, it must be below the damp proof course.

John Burry is the editor of http://www.lets-do-diy.com He has extensive experience writing for a broad spectrum of UK publications coveringindustries as diverse as health, automotive, beauty, new media and construction. Before taking up his current position he worked in PRwhere he was account manager for a number of blue chip clients. John has gained a reputation for detailedresearch and presenting information clearly and concisely.

Saturday, June 27, 2009

Home Contractor Problems and Solutions

This is one of the biggest problems in business today. You have some work done on your home in good faith that the contractor knows what he is doing. When all is said and done you have a problem that needs to be resolved as soon as possible. I really don't care how long it has been since the work was done. If you have a problem the least that your contractor can do is answer the telephone.

Some companies go out of business and others get to busy to respond to your problem. You will hear the old excuse "That's not my problem" or the ever popular " I didn't do that". I have been in business for over twenty years and had very few problems. Of course I built things to last as long as possible.

Keep in mind that some contractors are a one man operation and they might be on vacation. Some contractors do not answer their phones over the week ends or after business hours. So don't sink the ship to fast.

Do not call the Contractors Licensing Board or the Better Business Bureau unless it has been at least a few working days. I would give it at least a week or so. Oh yeah don't assume that the contractor got your message. Call a few times at the least.

It has always made me mad when I have to fix someone else's problems. I get the call when the other contractors won't respond. I listen to the home owner with regret for being in a business where I am considered a crook. This is one of the reasons why contractors in my business get out of it.

If you have the contractors address and they aren't responding by phone you can always send them a letter by certified mail. Request a return receipt. That's your proof that the company received your letter. Keep a copy for your files.

The good news for a home owner when a contractor will not respond to your calling them is the Department of Consumer Affairs. Most states have a complaint department of some sort that will listen to your complaints. Does this mean it will get resolved? NO there are no guarantees here.

If your state has a licensing board for contractors, this will be your next step.

This will get your contractors attention and there is a great chance they will respond now. If there are enough complaints against the contractor and they do nothing about them the contractors board will take their license away.

If your contractor does not respond after all of this. There is very little you can do about it. Hire someone to fix the problem and look at it as a very important lesson learned.

If your state doesn't have a contractors licensing board contact the Better Business Bureau or your local government for their recommendation. Ask some of your friends if they have had any problems like this and how they handled them.

For some more tips about hiring contractors go to
http://gregvan.com/library/homeowner_checklists.htm

Greg Vanden Berge has been in the home building and remodeling business for over 30 years. With this knowledge he has created a few websites that provide useful information for home owners as well as contractors. His main goal is to educate professionals in the home related businesses, dealing with problems that can easily be avoided with just a little bit of information.

His website http://gregvan.com provides all kinds of answers to remodeling and new house building issues that could create major damage as well as possible damage to your pocket book.

How to Know You've Got It

How can you know when you are-or are not-tapping into the Conquering Force in your life?

When You Don't Have It

When you are not tapping into the Conquering Force, you'll feel as if you're drifting like a stick in a river. Life will take you wherever it wants instead of you controlling where your life goes. You will set goals but never reach them, and you'll feel that life is ruling you. Maybe you'll even decide to accept the status quo, thinking you can't do anything about it. You may believe that you don't have any choices and end up accepting that you'll never achieve what you want in your life. Worse still, you may view your situation as hopeless-dying emotionally or spiritually because of your limiting paradigms. If any of these things are happening in your life, you haven't yet discovered that you do, indeed, have choices and can make changes. You were not born for mediocrity or unhappiness. Because of your ability to choose, you can control a lot more than you think.

When You Do

You will know the moment when you have tapped into your Conquering Force because you'll feel alert, alive, excited about your life, and you'll know you're in charge of what you're doing. You will be enjoying the path you are on. You can find a way to do what needs doing and get results. You'll go out and make things happen for yourself. Your indomitable spirit comes from your Conquering Force. You'll have a feeling of well-being and a sense of accomplishment. You'll be happy, even through the tough times. As you accomplish what you set out to do, you will be surrounded by both tangible and intangible evidence that you have unleashed your Conquering Force to achieve your Core Desires.

RELATED FORCES

Once you have discovered your Core Desires and unleashed the Conquering Force, ten other internal forces come into play: enthusiasm, joy, creativity, focus, drive, commitment, discipline, stamina, talent, and other resources.

Like cousins in a family, these forces are all closely related. Working together, they become synergistic and dynamic. Once you identify something you want badly enough, your mind automatically becomes more creative. You become enthusiastic, focused, committed, disciplined, and dedicated, and you make better use of your talents and other resources.

Tragically, most people don't know how to employ these forces. Through my own experience-and the vicarious experiences of countless others who have overcome difficulties, past histories, and seemingly insurmountable problems-I know that the ability to learn and perform is greatly enhanced when Core Desires trigger your Conquering Force.

If you put a l00-watt light bulb into a lamp, obviously you'll get more light than with a 25-watt bulb. So it is with the Conquering Force. Getting up in the morning and going to work may only be a 25 on the Core Desire Scale. However, you may come home at night and work at a furious pace until midnight to complete the boat you are building; this effort is at 100. It's an effort you enjoy, no matter how late the hour.

How can you judge how much power you're deriving from the Conquering Force? Use this "Power Meter" to rate yourself in each of these forces.

There can still be some achievement even when the Conquering Force is seemingly dormant, because you always have some degree of desire. But if the Conquering Force is engaged at a very low level, you may never get out of bed. If the Conquering Force is engaged at a moderate level, you will do your duties-assigned tasks, shopping, and other items on the routine of your to-do list, if these are things you have to do. But when the forces of your heart, mind, and will are engaged at high levels, you will tap into amazing energy, passion, and power.

Moreover, other people can tap into the power of your Conquering Force for their own personal benefit-especially when their Core Desires are closely aligned with yours. In these instances, you will become a leader or mentor to those who want to follow your example, pursuing a similar path to progress in their lives and careers.

By Jack M. Zufelt
"Mentor To Millions

Jack M. Zufelt is a bestselling author and has achieved worldwide recognition for teaching people the true cause of all achievement. His life's mission is to impart the truth about-and dispel the myths surrounding-success and achievement.

Want to achieve better results?

How about live a fuller life with more happiness, joy, and satisfaction? Discover Jack's DNA of Success and live the life you've always wanted... Click Here -> http://www.DNAofSuccess.com

Friday, June 26, 2009

Exterior House Painting

Spring is just around the corner and this article is all about giving the exterior of your house the paint job it deserves. As a professional house painter I would like to lay out five important tips that most people get wrong when painting the exterior of their home.

#1.) House Wash - I like to give the house a good wash before I paint it. I don't wash all four sides at once though. I usually do just one side (the side I plan on painting first) at a time because I'm going to be there for a week or two anyways probably. That way by the time you get to the next side there isn't a bunch of webs or sand or dirt built back up.

#2.) Choosing Colors - Some houses you drive by have weird colors. This is because they picked colors from a fan deck. For best results you should use an exterior house color brochure. Its coordinated color schemes help you to choose normal standardized colors. A standardized color chart will have perfect color matches that you should pick and choose from. Especially if doing two or three color schemes, you want a professional color-coordinated exterior brochure. These brochures are usually found at any paint store.

#3.) Use Quality Paint - I always use name brand paint on all my exterior house painting jobs. Why use inferior paint and waste all that hard labor? Especially if you are paying someone else to do the painting. I like Benjamin Moore exterior house paint. They have good time-tested exterior paints and primers.

#4.) Latex vs Oil Base - I always use latex paint on the outside or exterior of a house. Oil base or Alkyd coating tend to crack and peel. Latex paint can breathe and stays flexible. It lets the moisture out of the house. Oil base paints cannot. That is why you get cracking and peeling.

The only exception is when the you have bare wood. You want to prime it with an exterior alkyd or oil-base primer. Bare wood can cause "bleed through" stains that you can not block as well using a latex primer (Although nowadays some latex primers are actually getting good at stain blocking). But the main thing is that you want to use latex paint on your house's exterior and you want to use a good name brand exterior paint. Especially if you're a house painter and you're doing it for a homeowner. Don't show up on their door step with average name brand paint. People want the best.

#5.) Oil Base Stains - If you plan on staining your house there are many excellent exterior latex stains. Especially solid body stain. Solid body stain looks like regular paint except it's made for rough wood siding. Now if you have a natural wood color siding you will want to use a "semi-transparent" stain that is oil base. I would use an oil base stain in this instance because the oil base stain can permeate down into the natural wood. This is something that should be done every few years to keep the sun and elements from deteriorating the natural wood look. A quick one coat to protect the natural wood siding is best.

Lee Cusano has owned and operated his own successful painting business since 1991. He has also helped many others to start their own painting business with his "Paint Like a Pro Estimating and Advertising System". Lee also offers a new free report titled "How To Quit Your Day Job This Week and Double or Triple Your Income". To get it please go to http://www.Painting-Business.com

Antler Lamps and Chandeliers

Authentic antler lamps are an incredible addition to your home decor that creates the essential rustic lighting that most homes need. These hand crafted naturally shed antlers truly brings the outdoors to life in any room in your southwestern or country home. Each lamp is a unique, one-of-a-kind because of the genuine antlers that are found in spring after the deer, moose or elk have naturally shed them. If you wait too long to collect these treasures, small critters of the forest will chew on them for the calcium. Older sheds are generally more difficult to find.

Your country home decor will be complete with an antler lamp used as a table or desk lamp. The variety of styles and shapes are endless. However, you may like to have a hand crafted antler chandelier. Your kitchen decor especially, will be enhanced with this type of chandelier hung above your island. I have seen that they are beautiful hung above the dining room table to truly give an outdoor rustic look. To top off the beauty of the chandeliers, be sure to enjoy the glow from the natural rawhide chandelier shades.

Whether you choose to have leather or rawhide lamp shades, you will love the variety of shade colors. You may choose one of several colors in the pig skin leather shades as well as the rawhide laced lamp shades. Leather lamp shades have your basic color scheme colors for any home or southwestern decor. The rawhide shades are made of natural goat skin that is kept natural, bleached or dyed to create a colorful glow for your home lighting.

Log cabin decor would be missing something if it did not have a deer antler lamp as a part of its log home lighting. When you think of log cabin, you think of the outdoors, right? So definitely embrace the outdoors in your cozy home. You will find that these hand-crafted lamps are perfect for your cabin decor. You may even choose to hang a chandelier above the pool table in your lodge. These rustic lamps can be complete with pig skin leather or rawhide lamp shades, hand painted with a wildlife scene or of the many remarkable animals from the woods.

Another wonderful fact is that you may also have antler sconces to use as wall decor. These wall sconces have been beautifully made with real antler sheds mounted to a natural log plaque. Very unique in its appearance, these sconces are completed with rawhide candelabra shades. Your rustic decor will be outstanding with these one-of-a-kind pieces of art, whether it is for your lodge or a cottage in the woods.

Your western lighting will be exceptional when you have your own antler lamp. Being out west really reminds one of the memories from the early pioneer days. I am sure that along the wagon trails or during the search of a creek, they would stumble upon the natural sheds. Now, your southwestern home can be enhanced by the wall sconces or antler table lamps from genuine antlers. Who would have thought that a simple way of life would become a natural treasure for our western or country style decor needs?

You will definitely have unique home decor when you combine these rustic lamps with your additional country, hunting or wildlife theme. Some are crafted so artistically that it will make you delighted to have one of your own. Never settle for the ordinary pieces of home decorum. Be creative in all of your endeavors. Whether the table top, desk lamp, hanging antler chandelier or wall sconces, you can be thrilled to know that these antler lamps can set a perfect tone for your southwestern or country home.

Don't be taken advantage of by expensive specialty stores and middle men. You can get Antler lamps and Chandeliers directly from the artists at Mission Del Rey. They have a sale on this week. Plus, you can use private coupon code "article" for an additional discount off the sale prices, on anything you like. Learn more with free articles and tips too. Take a quick look... http://www.missiondelrey.com

Thursday, June 25, 2009

Transform Your Bathroom - Home Tips

When you don't have room in your budget to completely renovate your budget, it is amazing what installing a new bath vanity will do for the look and feel of this room of your home. The simple task of changing the cabinetry in the bathroom will make it look as if you have redone the whole room. Simply adding a few different accessories, such as changing the color of the towels of the shower curtains will enhance the effect.

A bath vanity does not have to be an expensive proposition with the many styles of discount vanities available. You do have to look at the size of your bathroom so that you get a vanity that will suit the space you have. For example, adding a large vanity to a small bathroom will make the room look crowded.

The vanities available in MDF are not expensive and require assembly. However, the detailed written and visual instructions that are included will make the assembly quite easy. Even the tools you need to put the various pieces together are included. All you have to buy extra is the sink and countertop, but there are some models that have this included as well.

The bath vanity is the central focus of a bathroom. This is where you will spend time grooming yourself in the morning before you go to work and when getting dressed to go out at night. You do need to have drawers and shelves where all your grooming aids are close at hand.

You can blend the old with the new by using an antique style that has a wash basin type sink that sits on the countertop. You can choose from a wide variety of colors, but the best rule of thumb to follow is to have a vanity that is of a neutral color. You can add contrast in the faucets and colors of linens that you use.

You do have to make sure that the bath vanity of your choice is sturdy and durable. You will not save any money by buying a vanity that is really cheap only to find that you have to replace it in a few years. A lot of the furniture manufactured today is eco friendly using glues that will not emit any harmful fumes into the air when they come in contact with water.

Even the smallest bathroom can have an elegant bath vanity or even a glass sink. A stone vanity, for example, can measure only two feet wide and will make a bold statement in your bathroom as well as make it look larger than it is. A vanity made of stone with teak cabinetry inserted in the center is also a viable option if you are looking for durable construction that will last for many years to come.

When you shop for a new bath vanity you can do so in many different ways by focusing on any of the following aspects:

Size

Shape

Material

Price range

Obviously the price will be the bottom line for you, but you will find that there are vanities to suit every taste. Browse the sites of the many online retailers just to get a glimpse of the wide assortments you can choose from. This will give you ideas to work with when you are contemplating making changes to your bathroom.

Allison Ryan is a freelance marketing writer from San Diego, CA. She specializes in home remodeling and interior design. For a beautiful bath vanity or glass sink for the bathroom of your dreams, please visit http://www.mybath.biz/.

Interior Decorating Ideas

It's happening again. The styles and fashions that we thought we'd seen the last of a decade ago are re-emerging as the latest thing in chic design and people are going mad for it. In fact, one of interior furnishings mainstays throughout the eras has been the humble lamp and while bench surfaces, chairs, lounges and most other room items have gone through drastic changes, many of the retro lamps that emerged in the 1950s and 60s are still preferred today.

The great thing about decorating in retro style is that almost anything goes, as long as it is fun, combines shapes and colors and looks unique. Floor lamps such as the Arco lamp that reaches from one side of the reading chair to the other still looks appropriate, as does the square lampshade on a wooden pedestal base. From there it's up to your own discerning eye as to how funky you want to make the lamp shade with options of trimmings, tassels or prints to bring out your retro preference.

The great thing about deciding on a retro lamp is that if you don't particularly like the look of the traditional lamps from the era, you also have the more space-aged looking lamps that were inspired by the exuberance of the post-war optimism. New products such as melamine spattered with chrome and designs that were sleek and sophisticated combined to produce a very forward thinking look.

The great thing about using the vintage retro lamps that your parents loved is that the burnt orange lamp shades or the avocado ceramic lamp stand is now cool again because, well because it's retro.

An important part of putting together a retro room is adding furnishings that follow the retro style. Picking out a fun and funky retro lamp should be enjoyed. Visit Retro Lamps Galore to help put that new retro-style room together.

Sunday, June 21, 2009

Internet Tales and Tips

You know, going down the Internet marketing trail the way I have...and approaching the Internet from an SEO perspective, I am able to observe how the net works and more importantly, how the programs that are designed for success for average people like me work.

Funny thing, most people just know that they need to buy some software program, some Internet marketing marvel, some latest and greatest program that will automatically make them highly successful and rich.

Programs that can range from $19.95 to thousands of dollars are being sold every single day to people with stars in their eyes hungry for the grand prize of Internet marketing success. This is not to say that some programs are good.

Some programs actually do assist people in building an online business, but the bottom line here is...the systems that legitimately work...that are time proven...that give the desired results of placing websites at the top of Google...are absolutely FREE!

That word free is too often used on the Internet today with a back end attached. Some programs may be sign into for free...but somewhere down the road, the people are going to be asked to part with some of that hard earned green stuff. Let's take a look at some FREE stuff that really is FREE!

Writing articles and then publishing them to great places like EzineArticles.com is one place that one can write articles...submit them...and if they meet the specifications of the owners of the systems, the articles will be published live on the net with all the necessary promoting properties that search engine spiders love. Original content, keywords and links. Those are the elements that drive the entire internet, and nothing more. The cool thing about EzineArticles is the fact that once that come up to the top of a keyword category, they stay there. They can be used as a precursor to the website. If someone clicks on the ezine article link, and reads about the url promoted, then possibly a contact is made. Again, free...just requires a little thought and effort. Writing press releases. Writing an effective press release is much the same as ezine articles; however, one needs to approach the press release from the aspect of making an announcement to the internet. A press release, when properly written, will come to the top of a keyword category within a few days. Here again, another precursor to the website promoted, as well as being another link directed back to the website. Since the internet is all about linking, this valuable tool is a great way to produce links for the website promoted. Totally free...and very effective.

Writing press releases. Writing an effective press release is much the same as writing ezine articles; however, one needs to approach the press release from the aspect of making an announcement to the internet. A press release, when properly written, will come to the top of a keyword category within a few days. Here again, another precursor to the website promoted, as well as being another link directed back to the website. Since the internet is all about linking, this valuable tool is a great way to produce links for the website promoted. Totally free...and very effective.

Blogging is a fantastic promotional tool and with the introduction by Google of the new Blogger.com, it is even better. When content is added to a blog...just another name for a website...and submitted to Google for indexing, a wonderful thing happens. Original content and yet another link going to the website promoted is made. When done consistently day by day...producing unique links every day...the process makes for a great way to get URLs promoted to the top of a keyword category. Totally free...and highly effective, but as usual it does require thought and action.

Creating and posting to forums.These are a great way to get URLs out on the net, but a great many people do not realize that a forum is absolutely free to obtain...and after consistent posting to forums (their own forums) with good original and relevant content, Google may even attach a spider robot there to make indexing a regular occurrence. Here again, consistently writing good information about the website promoted. Again...a great all FREE tool for promoting websites.

A question is raised here...why would good money be spent, when it is not necessary? Ah, the age old dilemma that most people fly by the great things, in the ultimate search for the easy way out...to which there is not an answer.

Butch Hamilton is an SEO|SEM Specialist. Living on the internet has become a way of life...a succesful way of life. His talents for obtaining top positions on the search engines have led him to the point in his life where he has always wanted to be.

"Life-What a Ride!"

Says Mr. Hamilton, "Writing has always been my passion. Gone are the days when I placed blatant ads on the internet for exposure. I have found my life's work in writing articles.

Reliable and credible information is what the internet is all about to Butch Hamilton. His experience as a self employed building contractor...steel fabrication...has led him on an incredible journey.

He now resides in his beautiful home in Texas with his wife. Writing is the passion behind his successful promoting ability on the net.

Butch Hamilton's Quote: "What we think-is what we become."

http://ButchHamilton.com
http://butchhamiltonsbestdomains.com

Hardwood Floor Installation and Floor Sanding - Choosing the Right Surface Treatment

Consumer interest in hardwood floors is increasing, and so is the awareness of different surface treatments. There are several different options to choose from such as finish, oil, and wax. To finish a wooden floor is the most common treatment consumers tend to go for.

The difference between finish and oil is that a finish builds up a surface. This surface is a protecting layer, and the resistance depends on how wear resistant the finish is. In contrast, oil gives the hardwood floor an impregnation. The hardness and wear resistance of the wooden floor is critical to the survival of the floor.

A number of factors influence the choice of treatment. Finish and oil have advantages and disadvantages making them more or less suitable for certain environments. The advantage of a finish is that you can get unbeatable wear and tear resistance. Finished wooden floors are also easy to clean and maintain. Finish is available in gloss, silk, matt, and satin.

The advantage of oil is that it more often than not looks great. It is scratch resistant. There is also the possibility to spot repair worn or damaged areas. The use of oil in public places is more suitable on dark wood. The oil enhances the colour, and the dirt is not as visible as on lighter wood. But not only does the shade of the wood flooring affect the choice of surface treatment, the hardness of the wood is important too.

It is also very important to choose the right type of wood for a specific environment. For example, the use of oil on a ash floor in a shop would not be a suitable treatment, unless you are willing to put a lot of effort in maintenance. Ash is a light kind of wood and shop floors tend to have heavy traffic. Other examples of light kinds of wood are beech, pine, and maple, which are also not suitable for public areas with high traffic.

A sports hall floor is also not suitable for oil. The reason is that sports hall floors need regular cleaning, and that means that the oil is washed away, and the floor would need regular maintenance. Wooden floors add beauty and value to your home. Choosing the right surface treatment will result in a beautiful, durable, and easy to maintain wooden floor.

Martin Stepien is the owner of Starlet Building a building contractor in London who specialises in hardwood floor installation and floor sanding.

More information about hardwood floor installation and floor sanding services in London is available on the Starlet Building website http://www.StarletBuilding.co.uk

Other services that Starlet Building offers include kitchen installation, bathroom installation, painting and decorating services, and carpentry and joinery services.

Starlet Building has extensive public liability insurance. All work is guaranteed for 12 months. References from previous customers are available on request, and free quotations are available on all building services in London.

Preventing Damage to Septic Tanks - Home Repair Advice

Septic tanks, like all other products, need periodic maintenance to function properly. And if something goes wrong anywhere in the septic system, the costs can be huge. Apart from periodic maintenance and inspection, it is also necessary that we use our drainage lines properly. This article discusses the basics of septic tanks and some typical things that we shouldn't do if we want to increase the life of the septic system.

Let's first see how septic tanks function properly for so long without maintenance. Whenever something goes out through the drainage lines in our homes, it goes to the septic tank initially. Visualize of it as a gigantic tank that is usually made of concrete though very old ones are probably made of steel. The drainage lines enter the tank through an inlet tee near the top, while there is another outlet tee at the other end from where liquids leaves the tank and goes to the drain field into the soil.

Upon water entering via the inlet tee, the solid materials often sink to the bottom of the tank make a sludge. Some solids that don't sink inside the water gather at the surface along with grease and oily liquids forming scum. Since the outlet tee is at a certain height, solids from the sludge usually don't pass on to the drain field. Likewise, the tees keep sludge and dirt away from the out and inlet.

Bacteria within the septic tank help to liquify the solids, ensuring that they don't build up too much. This is the manner in which septic tanks continue functioning well - unless damage occurs to them, which it usually does eventually. The issues most often happen when debris reaches the out or inlet. So the only way to keep the system running smoothly is by pumping the waste out of the tank before the sludge or scum become overgrown in volume.

Nevertheless, you still need to be careful in your routine life to increase the performance of septic tanks. Firstly, the drain field should not be damp with rainwater; if it is already overloaded with water from other sources, it would not be able to efficiently absorb the water coming from the septic tank. Likewise, make sure that your internal draining lines are not putting an unnecessary amount of water into the septic tank. A common reason for this can be leaking faucets or overrunning showers. So fix these problems whenever you come across them.

Secondly, do not plant trees close to septic tanks as the roots may grow into the equipment and cause problems. And don't throw all sorts of garbage into your drainage system. Diapers, condoms, napkins aren't usually broken down into liquids by bacteria and would quickly pile up the level of sludge inside the septic tank. Additionally, ensure you do not use chemical cleaning agents in substantial volumes; these cleaners typically eliminate bacteria inside the tanks and hinder the processing of liquefying solids. And most importantly, never drain grease or other oily liquids; these would gather inside tanks as scum and may even harm the soil and drain field if they escape through the outlet.

Take all these precautionary steps and you will rarely face problems with the septic system.

Scott Rodgers is a plumbing professional who has worked with septic tanks for many years. If you want more information on septic tanks or a qualified plumber to help you repair damage to your tank, visit http://www.eLocalPlumbers.com

Home Improvement Consumer Laws Can Help You in Many Ways

There are several home improvement consumer laws that have been created to help the consumer who are working with contractors for their home projects. These consumer laws are different in different regions but one must be aware of all of them to take maximum advantage as well as to avoid any kind of troubles. Here are some of the most important home improvement consumer laws that can help you in your daily life.

You Have a Right to Cancel Your Contract

The federal government gives you the rights to cancel any kind of contract you signed within three days. This law has been created to support a consumer who happens to change his mind after signing a contract. So, in case you change your mind after signing a contract, you have three days to cancel the deal without any troubles. You have the right to do so.

Don't Forget the Cancellation Form

When you cancel a contract, make sure you get two cancellation form of the contract from your contractor. One of these forms is for your record while the other one is for the contractor. You have to clearly mention all the details of the contractor, and the reason for canceling the contract. Make sure you ask for it from your contractor after canceling a deal. Majority of people are not aware of such home improvement consumer laws and they do not ask for any kind of documentation when they cancel a deal.

It is Your Right to Ask for a Contractor's License

Many states do not allow any contractors to work without a contractor's license. If you do not know about home improvement consumer laws of your region, you should make sure that your contractor is registered and has a valid license to work in a particular region. Otherwise, you might have to face several problems if your contractor does not have a contractor's license.

Avoid a Bad Contractor

Make sure that the contractor you hired for your project has a good working reputation. Otherwise, if there is any kind of complaints signed against your contractor, you will not be able to proceed with your home improvement project according to home improvement consumer laws.

These laws are different in different regions but you can always research on the internet and get yourself updated to use these home improvement consumer laws for your best.

For detailed articles on home improvements projects and contractors, visit http://www.theyarelocal.com/articles/index.php.

Friday, June 19, 2009

The Benefits of Hiring an Electronic Systems Contractor

The demand for the latest and greatest technology continues to grow at lightning speed and as a result the task of sorting through the mass array of high-tech wizardry as it pertains to home technology systems such as home theatres, home automation, whole house audio and video, security and CCTV systems, wireless networking, smart wiring, and lighting control solutions can be a daunting task to say the least. So who do you turn to for advice on sorting through it all?

Enter the Electronic Systems Contractor (ESC). So what exactly is an ESC you ask? An Electronic Systems Contractor is a company that provides sales, installation, and service on life safety systems, sound communication, entertainment, and environmental control systems. These professionals are highly skilled, trained and certified in this specialized field.

After youve determined exactly what kind of home technology system you want to install and what you want to get out of your system, the second step is to hire a qualified ESC or more commonly called an Electronic Systems Integrator, who will help you establish a workable budget, listen to your primary objectives as it pertains to your project and your lifestyle, and then design a system that will surpass your greatest expectations

If you are building a new home, an ESC can be just as an important resource as your interior designer, architect, and/or builder. In fact, an ESC should be brought in early during the initial design phase of your new home to ensure optimum savings on your overall budget as it is much easier to pre-wire rooms prior to the drywall phase of construction than it is to go back and try to retrofit a room. Keep in mind that long-term dependability, reliability and quality in a home technology system are the most cost-effective attributes you can build into your new home.

Technology changes so fast and often times the electronic components some of the box stores purchase in large quantities quickly becomes out of date as it sits on warehouse shelves waiting to be sold. Whereas an ESC will always have the latest and greatest products to offer as everything is custom-to-order. So you can be sure you are getting the latest technology for your money.

Adding a home technology system to your home is a huge investment and by hiring a qualified Electronic Systems Contractor to design, install and maintain your system, you can take comfort in knowing that youll be in good hands from start to finish and well beyond the installation process.

Curt Rothenberg is Founder of Accent Electronic Systems Integrators, a low voltage electronic systems contractor located in southwest Florida that offers home automation systems, custom theatres, audio, video, security, CCTV, wireless networks and lighting control solutions for both residential and commercial applications. For more information please visit http://www.accentesi.com

This article may be copied or reprinted provided no changes are made to it's content and the complete author box is included.

Wood Post Repairs

Using Home Safes For Added Family Security

Protecting your valuables with a home safe provides you with the security in knowing that its there to protect your irreplaceable items from theft or destruction. It gives you that piece of mind knowing that your money, important documents, firearms, jewelry, and family heirlooms will be safe even through fire or water damage.

It also protects the wandering inquisitive child, babysitter, housekeeper, etc, from stumbling upon items that you would rather they not see.

But you just don't go to any discount store to get your safe, then bring it home and plop it in your closet. There are some things to think about first, a bit of thought and planning.

What type of protection are you looking for? A home safe should protect your items from fire, water damage and theft. You can find safes that protect from any one, combination, or all. (You may still want to place some of your valuables in plastic bags just in case of water damage.)

What style are you looking for? A home safe can be anything from a small chest, file, wall or floor mount safe to a home or business safe or file cabinet. You will want to install it away from the master bedroom or closet - this is the first place a thief would look.

What size are you looking for? What are you trying to protect? Your home safe should be big enough to fit things like important documents (birth certificates, passports, social security cards, credit cards, wills, tax returns, business papers, insurance documents, photos, etc); digital media (CDs, DVDs, memory sticks, GPS systems, MP3 players, cell phones, etc), and valuables (family heirlooms, jewelry, cash, video/camera equipment, collectibles, etc).

The safe needs to be anchored in some way, so be sure you will be able to bolt the safe to the floor, permanent shelving or set it in concrete. After all, you don't want to make it handy for the theft to just pick up and walk away with everything all in one spot! It should have a tool resistant outer shell as well as a minimum of one-hour fire rating; most safes have a 20-minute fire protection. The lock should be U.L. approved.

Use your safe everyday so it becomes routine. Protect the safe code and change it occasionally. There are also models available that open using your fingerprint (very cool!).

To get more valuable free personal and family safety tips, go to http://MyFamilySafetyInfo.com/ Please also visit http://GuscleBerry.com/ for a variety of home, yard and garden decor and gifts, all at affordable prices along with bulk purchase discounts.

Hard Water Deposits In Toilet

Contractor In Southern California

So you want to make big money making a living as a contractor in the state of California. Well now I bet you have seen contractors on TV or maybe you know someone who is a contractor. You see these men and women playing the part as Mr. or Mrs. Money bags. If you have the slightest thought that becoming a contractor will provide you with a life of riches think again.

Most contractors that I know and have worked with over the years don't think of there jobs as easy. They have to work everyday and a lot into the night doing estimates or meeting with potential clients because they are to busy during the day. The life of most contractors in the beginning will be difficult to say the least. But if successful you will make a great living for yourself and your family.

Now that we got the false illusion of the contractor answering his cell phone all day at some nice golf course having lunch talking about the money that he just made selling his oil stocks. We can start on reality. If being a contractor was that easy everyone would be a contractor. Right..... Well maybe not everyone.

I have been a contractor for over 22 years and in construction for 30 year. I have seen a lot of changes over the years. I remember when a few contractors that I worked for made a lot of money during the late 1970's. These guys had Ferraris and money to burn with one exception they had no idea how to save any of it. These guys went on vacations and bought extravagant toys for them selves. Out of most of the big framing contractors I worked for about 10 percent are still in business or actually saved their money during the good times so that they could make it through the bad times.

These contractors never thought it was going to end. Life on easy street that is. But it did and most went by the way side. I guess that is the nature of business. Especially the current economic business cycles that we seem to go through over the years. If you don't have the money to advertise or carry a payroll. Your business is going to suffer during the bad times. Sure there is credit and bank loans but you still have to pay that money back. IF you can't save your money stash some away for advertising.

Some of the best advice I can give a contractor anywhere especially in the state of California is " Don't Think The Great Times Of Easy Money Will Last Forever". Save some of the money you make just in case you need to get through the bad times. You will thank me for this latter, Some time down the road. Take this advice and put it into action starting right now.

Greg Vanden Berge has over 30 years of experience in residential home building and remodeling. This provides you with the comfort of knowing that you have a professional with the knowledge and skills to complete your construction projects in a timely manner.

Our low overhead along with our new online estimating system will provide you with the most competitive construction pricing in the area. We continue to educate ourselves about the new home improvement books and building systems in the construction industry. If we have any doubt that something might not work we don't use it. We have found some of these products to be the root of some major home building problems.

Click on the Home Remodeling Ideas to get more information and a possible online estimate for your home improvement project.

What Does A Gfi Do

Injection Waterproofing - Home Repair Tips

Injection waterproofing is often used to fill and seal cracks and crevices. The material is most often made from a polyurethane compound. The compound is lightweight and expands up to twice its original size when applied to a surface. Many non-toxic and environmentally safe products are available at home improvement stores nationwide. Injection waterproofing is used mainly in foundation crack repairs.

In most foundation cracks, a polyurethane injection can seal the opening. In some smaller cracks it may be apparent that a sealant was used because it may be difficult to evenly inject the compound. Single caulking style cartridges and the dual side-by-side cartridge systems are the types of injection waterproofing compounds available for retail purchase. Both of these are manually injected and easy to pump.

When using an injection waterproofing method, it is important to keep the area dry. Temporarily block any flowing water to the area, and clean and dry the area as needed. Experts say that in the case of water flowing through a hole, you can temporarily caulk the hole with candle wax, modeling clay or plumbers putty. If the cracks are in narrow or hard-to-reach places, you can use a flexible hose attached to the injector nozzle.

Whatever waterproofing system your leakage problem requires, be sure to do your research. If you choose to make this a do-it-yourself project, make sure you know where your leaks are coming from and the proper method to repair them. When purchasing waterproofing materials you should make sure you are buying the appropriate product for your needs. The National Association of Waterproofing and Structural Repair Contractors (NAWSRC) has tons of information on waterproofing. Whether or not you decide to hire a contractor, this organization can help you from beginning to end.

Waterproofing Info provides detailed information on waterproofing systems, including injection waterproofing, foundation waterproofing, concrete waterproofing, deck waterproofing, basement waterproofing, and waterproofing basement walls, as well as waterproofing contractors and consultants. Waterproofing Info is affiliated with Business Plans by Growthink.

Fixings Squeaking Stairs

Thursday, June 18, 2009

Asphalt Shingle Roofing - The Facts

Is it any wonder why almost 80% of homes in North America use asphalt shingles as the roofing material of choice. The prevalence of asphalt shingles has created a vast assortment of fittings and fixtures designed to work with them. Items such as a multitude of flashing configurations, edge products, and almost every skylight manufactured has an appropriate base configuration for a weatherproof connection with asphalt shingles. All of the material that you need for a proper installation, such as the shingles, tarpaper, nails, vent boots and chimney flashing are available at any home improvement retailer.

The primary attributes of asphalt tiles are:

  • reasonably priced (economical),
  • require very little maintenance,
  • versatile,
  • provide excellent protection on steep sloped roofs,
  • are weather and sunlight resistant,
  • easy to cut,
  • can be nailed by hand or with powered nailers.

There are two different types of asphalt shingle base material construction - composition and fiberglass. Composition shingles use a base material termed organic felt, which is a blend of paper and wood fibers. Fiberglass, on the other hand, uses a base that is comprised of a fiberglass mat. In both cases, once the base material is produced it is soaked in an asphalt compound. In numbers sold, fiberglass leads the market. They are less expensive, weigh less because they are thinner, have a longer wear life and have a better fire rating than the composition base shingles.

Average cost of a shingle roof is $50 to $150 per square, installed. Removal of old shingles will cost between $30 and $50 per square.

Both types of asphalt shingles are manufactured with embedded mineral granules. Seeing the granules in your eaves trough (after the initial installation) is a sure sign that you need to repair or replace the shingles.

Where just a few years ago asphalt shingles were only available in simple tab configurations in blacks, grays and browns, the manufacturers have expanded their product lines to include a vast array of colors, profiles and with the use of laminate coatings have created as assortment of eye pleasing textures. Special chemicals are also being blended into the shingles to make them mold and algae resistant. Although these additional features do increase the price per square, asphalt shingles are still the most economical roofing material available.

Drawbacks:

The serviceable life of asphalt shingles is the lowest of all the roofing materials. Although they are available in numerous grades designated by the expected life, from 15 to 50 years they often need repair or replacement long before their supposed life has expired. The hotter the climate, the shorter the life of asphalt shingles. Many of the asphalt shingle problems that are encountered by homeowners are a direct result of two factors:

  • poor initial installation
  • damage due to sever weather

Poor installation usually occurs in the area of deck preparation, and not providing adequate flashing around items that are protruding through the roof such as vent pipes and chimneys. Other poor installation methods are not using the required amount of nails per shingle and nailing in the wrong area of the shingle. There are many fly-by-night roofing companies that will quote low prices, because they won't be around to stand behind the workmanship. Choose a roofing contractor carefully.

Roof Repairs:

You should inspect your shingled roof and all the flashing at least once a year and after any major storm such as a hurricane. Hurricane winds will remove entire shingles and lift others. Sun and rain can cause asphalt shingles to crack. You should also go into the attic and look up, any sign of daylight means that there is a hole. When inspecting the roof look for shingles that have lost the granule minerals - bald spots, cracked and/or curled.

If you have to make a roof repair, choose a warm day so that the shingles will be flexible and unlikely to crack when lifted. The roofing cements also spread easier in warmer temperatures.

You will know when you have a roofing problem when you see beige spots appearing on ceilings and walls close to the ceiling. Beige spots are a sign of water damage.

Maintenance:

Roofing cement is the equivalent of duct tape for roofs. It will repair most leaks, cracked or torn shingles, patch flashing around vent pipes and chimneys. You can also use the roofing cement to cover nail heads that have been exposed.

Shingles fade with age so any replacement shingles used will most likely be visually obvious. Shingle over damaged ridge shingles, by nailing down all the corners of the old shingle first - do not remove them.

If you have to replace an entire shingle, lift each of the tabs and pry the nails out of the shingle of the one that needs to be replaced. Remove the top corners of the replacement shingle and very carefully, without damaging the tarpaper, slip it under the existing shingles.

Use roofing nails (large head, galvanized) to fix the new shingle to the roof decking. Use roofing cement to cover the nail heads.

Planning and knowledge are the keys to any successful home improvement, remodel or landscaping project!

For additional information on roofing materials for your home or other renovation projects, including landscaping, visit Renovation Headquarters

Insulation Blocking Attic Vents

Prevent Pinhole Leaks & Slab Leaks & Conserve Energy by Controlling Your Hot Water Circulating Pump

If you have had 1 leak, more will surely follow - you can do something about it before further damage is done and additional money is wasted.

Circulating hot water is the fastest way to wear out your pipes. In fact 90% of all pinhole leaks and slab leaks happen in hot water lines for the following reasons:

1. Chemicals in water are corrosive

2. Chemicals in water when heated are even more corrosive

3. Chemicals in water when heated and circulated through copper pipes that bend around corners and turn up walls and curve around electrical conduit and sewer pipes and are reduced in size as water passes through a building is extremely corrosive

In order to understand the solution it is helpful to know what causes the problem. With a little insight into how domestic hot water recirculation lines or recirc loops are built and how they work we can see that the answer is as easy as flipping a switch.

Apartments, hotels and larger homes have recirc loops designed to move hot water to the farthest fixture from the boiler or water heater in a reasonable amount of time. Each loop has a pump pushing water through a copper pipe 24 hours a day, 7 days a week. Each loop has multiple joints and fittings that obstruct the flow of water. Gate or ball valves and flapper checks and expansion tanks and whatever else the plumber had on his truck the day he built the line create disturbances in the flow path.

Water likes to flow in a nice straight line with no obstructions. This is called laminar flow - nice and smooth. Anything in the flow path can disrupt the flow and cause an eddy to form. Eddies are the bad boys, the unwanted visitor, the black sheep of the family.

Create a little friction, add in some turbulence and the next thing you know you have a leak.

As your reading this please keep in mind there are things you can do to reduce or even eliminate leaks. They are relatively inexpensive and I'll tell you what they are in a minute.

When water pipes leak many things can happen - none of which are any good. Pinhole and slab leaks, mold, wasted water, wasted energy, property damage, resident/guest complaints and inconvenience all mean one thing.

It cost you time and money.

The only question left is how much? Please refer to Table 1 for an idea of how much a leak can cost.

Table 1: The Cost of a Leak

1 $200 You caught the leak early and it wasn't buried in a wall or under a slab

2 $1,000 The leak was in a wall and you caught it early and it was relatively accessible after tearing out some drywall

3 $2,000 Same as above except you didn't catch it early and mold and light structural damage had occurred

4 $10,000 The leak was underneath a concrete slab but you were able to pinpoint the exact location

5 $20,000 Same as above except you had to chase the leak into another rooms

6 $100,000 + The leak went unnoticed until someone got sick and you got sued

So there is the doom and gloom. What's the solution?

Good question. The answer is there are a number of things you can do. As you go through my list keep in mind that people only use hot water 15% to 20% of the time (based on a study by the California Energy Commission).

First, check your water pressure. 40 psi is high enough for most 1 or 2 story buildings. Be sure to check it in several places to find the lowest pressure in the building. Typically that would be the point furthest from the water meter. If you don't have a pressure regulator, put one in.

When implementing this strategy do it in stages. Drop the pressure by 5 psi at a time and wait to see if you have any complaints. Shower heads and aerators already restrict flow to 2.5 gpm or less. Newer fixtures like the Evolve line of low flow shower heads have pressure compensating technology built into them and work just as well at low pressure as they do at high pressure.

Second, turn off the pump when no one is using hot water. That's right. I said turn off the pump. As I mentioned earlier people only use hot water 15% to 20% of the time. The pump only needs to be on when people need water.

There are 3 methods of implementing this strategy:

1. The Manual Method

2. The Guessing Method

3. The Automated Method

Manual Method

Have someone go to the switch and turn on the pump when you need hot water and turn it off when you are done. Might be practical for a single family home (certainly not convenient) but impossible in an apartment or hotel.

The Guessing Method

Plug your pump into a timer and guess when hot water will be needed. This may be a practical solution if the number of people living in the house or apartment or with a limited number of guests in a hotel and everyone has the same predictable need for hot water. Unfortunately when hot water is needed during an off period the timer gets disabled and never turned back on.

The Automated Method

Think about your recirculation line as a closed loop. When there is no demand for hot water, no water enters or leaves the system. When a hot water faucet is turned on there is a "leak" in the system.

When water leaves the system more water is added from the city water line through a cold water make-up line (this is the technical name for the copper pipe that brings cold water to your water heater).

If a flow sensor is placed in the cold water make-up line, any indication of water movement would mean someone is using hot water.

If the sensor sensed a demand (i.e., someone turned on a hot water faucet) it could turn on the pump. The demand would be met and the pump could be turned off automatically when the demand ended.

That is precisely how an On-Demand Intelligent Pump Controller works. The pump is only on when there is a demand.

As it turns out, there are many benefits to automating your recirc pumps operation:

Drastically reduces pinhole leaks and slab leaks - if the hot water is not moving, it is much less corrosive

Energy is conserved - since people only use hot water 15% to 20% of the time, the pump will be off 80% to 85% of the time. That means the recirculation line isn't full of hot water and no energy is being lost. California Energy Commission studies indicate 37% less energy is consumed when an On-Demand Controller is installed.

Note: A sufficiently high speed pump is required (2,200 rpm or faster) to implement this strategy. If you have a high speed pump you will only need an On-Demand Controller. If not you will need a full system including a high speed pump.

In conclusion, cut your risks, lower your losses, reduce your energy bill and extend the life of you pipes and water heater or boiler by turning off you recirc pump with an On-Demand Intelligent Pump Controller.

Contact me directly at the email address below to find out if this solution will work for you or what other options you might have. To purchase the On-Demand Intelligent Pump Controller click on the link below.

Do it now and sleep better tonight knowing that one of your biggest headaches just got cured.

For information on the On-Demand Intelligent Pump Controller go to http://www.SavesYouEnergy.com

Mark Franklin is CEO of Saves You Energy, LLC a manufacturer and retailer of water and energy conservation products. As a civil engineer Mr. Franklin was involved in the design of multi-family and commercial projects worth in excess of $100 million.

Mr. Franklin has worked with companies ranging from the US Navy to Embassy Suites and Biltmore Hotels to Stanford Student Housing. Pinnacle Properties, United Development Group and ConAm are among the apartment ownership and management companies that have used his products. School Districts like the Blue Valley School District in Kansas and ESCOs such as Johnson Controls have utilized his technologies to reduce energy consumption.

Mr. Franklin can be reached at mark@SavesYouEnergy.com or visit his company's web site at http://www.SavesYouEnergy.com

Floor Joist With Mold

Friday, June 12, 2009

The Bible's Power Over One Child

I mentioned Sean in another one of my articles, the story of a young foster boy that we were taking care of. Sean's father was my ex-wife's uncle, and they were going through some tough times for a while and their three children ended up as wards of the state. We eventually ended up taking the oldest child because he was the hardest one to place and another home. His brother and sister ended up with a family that wanted to adopt them and eventually Sean went to live with them and I believe all three of them were adopted by this family. I don't know this for a fact though.

Sean was a emotionally damaged child. His parents would punish him with some strange and bizarre punishments. They weren't really physical punishments but seemed to leave the emotional scars on him and I often think about where he is and what he is doing.

We watched him for about a year and I learned quite a bit from this young man. He was in the third grade but was still at the first grade level for reading and math. I would spend a couple of hours each night during the week helping him with his schoolwork, I seem to have created some sort of allusion that I would be able to bring him up to the third grade level within a short period of time. Wrong. He must've had learning disabilities and of course I don't think I was that good teacher.

Sean was easy going, polite and extremely obedient. He would do anything to avoid getting in trouble and often blamed others for his mistakes. His punishments must have been more than he could bear before he arrived at our home. I think you're getting the picture about what kind of a child Sean was.

One day I found myself in a dilemma with Sean, I couldn't get him to tell me the truth, even though I knew he was lying. I forget what the problem was but I remember a hollow look in his face. It was almost like he wasn't really there. It was almost like he was just doing time, sitting on the bed, listening to me asking the same question over and over again, "Sean are you lying", but he wasn't even paying attention.

I normally would not punish my children for accidents, and never tolerated lying. I was trying to explain to him that he wasn't going to get in trouble, I just wanted to know the truth. He wasn't budging at all and stuck to his story. I remembered that his mother and father were Catholics and feared the church, almost as much as they loved it.

That's what I came up with my evil plan. I don't know where I come up with these ideas, but every once in a while one pops up in my head and I run with it.

I told Sean that I was going to bring the Holy Bible in, and if he could swear on the Bible that he was telling the truth, I would accept that and this would be the end of our conversation. I couldn't believe my eyes, as he started crying and screaming, frantically and excitedly as a yelled out, I did it, I did it, don't bring the Bible in, I won't do it again.

I couldn't believe that was all it took to get information from him. I have always been a pretty good interrogator and found myself gathering information from those people easily, but this was amazing. His fear of the Holy Bible got me thinking about how powerful this book actually is to some people. I remember when I looked upon this book, pretty much the same as Sean did.

It's just a book, like any other book. It's not made at a holy factory or a secret monastery in the Swiss Alps somewhere, it's made from paper and ink and can be damaged and destroyed like other books. I would be surprised if I threw the Bible into the fire, that it wouldn't burn. I would be even more surprised, if I seen three men standing in the fire, wait a minute that's another story in the Bible.

Is it possible for this book to actually control the lives of people. It seemed to control Sean, I wonder if I, could have actually been driving a nail home that his parents started. Could I have added to his belief, that the Bible is a book from God the creator of everything.

Greg Vanden Berge is a published author, internet marketing expert, motivational inspiration to millions of people all over the world and is sharing some of his wisdom with experts in the fields of writing,marketing, and personal development.

Greg is currently working on a video library filled with great movies on a wide array of topics, like religion, self help and spiritual changes in the world. His views on religious freedom are slowly changing the way people think about institutional religion. Simple Words Create Powerful Beliefs.

Fireplace Drywall Ceiling Damage

Surviving As A Contractor In California

So you want to make big money making a living as a contractor in the state of California. Well now I bet you have seen contractors on TV or maybe you know someone who is a contractor. You see these men and women playing the part as Mr. or Mrs. Money bags. If you have the slightest thought that becoming a contractor will provide you with a life of riches think again.

Most contractors that I know and have worked with over the years don't think of there jobs as easy. They have to work everyday and a lot into the night doing estimates or meeting with potential clients because they are to busy during the day. The life of most contractors in the beginning will be difficult to say the least. But if successful you will make a great living for yourself and your family.

Now that we got the false illusion of the contractor answering his cell phone all day at some nice golf course having lunch talking about the money that he just made selling his oil stocks. We can start on reality. If being a contractor was that easy everyone would be a contractor. Right..... Well maybe not everyone.

I have been a contractor for over 22 years and in construction for 30 year. I have seen a lot of changes over the years. I remember when a few contractors that I worked for made a lot of money during the late 1970's. These guys had Ferraris and money to burn with one exception they had no idea how to save any of it. These guys went on vacations and bought extravagant toys for them selves. Out of most of the big framing contractors I worked for about 10 percent are still in business or actually saved their money during the good times so that they could make it through the bad times.

These contractors never thought it was going to end. Life on easy street that is. But it did and most went by the way side. I guess that is the nature of business. Especially the current economic business cycles that we seem to go through over the years. If you don't have the money to advertise or carry a payroll. Your business is going to suffer during the bad times. Sure there is credit and bank loans but you still have to pay that money back. IF you can't save your money stash some away for advertising.

Some of the best advice I can give a contractor anywhere especially in the state of California is " Don't Think The Great Times Of Easy Money Will Last Forever". Save some of the money you make just in case you need to get through the bad times. You will thank me for this latter, Some time down the road. Take this advice and put it into action starting right now.

Greg Vanden Berge has over 30 years of experience in residential home building and remodeling. This provides you with the comfort of knowing that you have a professional with the knowledge and skills to complete your construction projects in a timely manner.

Our low overhead along with our new online estimating system will provide you with the most competitive construction pricing in the area. We continue to educate ourselves about the new home improvement books and building systems in the construction industry. If we have any doubt that something might not work we don't use it. We have found some of these products to be the root of some major home building problems.

Click on the Home Remodeling Ideas to get more information and a possible online estimate for your home improvement project.

Drywall Repair For Damaged Walls

Wednesday, June 10, 2009

Stair Building Deck Video

Stair building tips for installing lights and decking, handrail tips and some deck advice.

For more helpful home improvement information visit: http://www.gregvan.com

Stair Building Tips

Missing Grout In Shower

Remodeling Professionals Needed

How would you like to help other contractors, home improvement specialists, builders, real estate professionals and anyone else involved in home remodeling. If you have any tips or home improvement advice to you would like to share with our readers, it would greatly be appreciated. Leave all comments below.

Small Crack In Roof Rafter

Monday, June 8, 2009

New Home Buyers Beware

Ican't believe how many homebuyers purchase a house, with very little information and a Lotta hope. I'm a general contractor and often work on these homes, after they have been purchased and a homeowner has their money, the real estate professional is no longer involved in the transaction and the new homeowner is starting to experience the pitfalls from buying the home, that they sincerely believe was in good condition.

It's usually somebody like me that gets involved with the new homeowners after everyone else is out of the picture and chooses not to return their phone calls or explains to them quite simply, it's not our responsibility, you're the new homeowner and we really feel sorry for you, please call us again if we can help you with anything.

You couldn't even help me with that, why would I want to call you again if I had a problem. I never could understand this thinking but have ran into it often. It sounds like an oxymoron when someone refuses to help you but offers you help in the future. What ever!!!.

If homebuyers had something else to rely on besides their real estate salesperson, home inspection service, mortgage or insurance professional, I believe they can eliminate some of these problems. Where do you start and how do you get the information. You can gather information from reputable people, books, the Internet and so on.

The problem is how do you know these people are reputable and the books on the Internet have good information. This brings us to another problem, but I've got the solution that will help eliminate some of the grief. I'm not going to remove all of the grief from your life but have a suggestion for you that will eliminate some of the pain when buying a home.

Arm yourself with a good home inspection checklist. You can search the Internet and they have quite a few good home inspection checklist to work with. These checklist can provide you with things you might not have thought of, and this is where you can eliminate some of the problems.

If you took one of these checklists with you while you were shopping for a home, you would be aware of some of the problems with the home. You might not find all of the problems but these checklist will help you with some of the problems.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He has just finished a Home Buyers Guide to take some of the frustration out of home shopping.

If your looking for some more home inspection or home building ideas.

Listen To Your Own Advice

When We Choose Misery Over Happiness

I am not one to feel sorry for most people. They seem to have a unique ability to cause themselves the most damage during certain parts of their lives. I have met some pretty self destructive people in my life. Being raised by a mother that lived in misery and love.

My mother had a difficult childhood. It seemed as if every corner she turned there was a obstacle either right in front of here or waiting just around the corner. Her father died when she was 12 year old. He was a farm laborer and didn't make much money. In other words they were poor...... She got sent to live with a few foster families and according to her she was molested by one of the fathers she lived with.

Soon her older sister invited her to live with her. My aunt was married to the owner of a pottery business and had 2 children about 10 years younger than my mother. My aunt soon realized she had a live in baby sitter that allowed her to stay out drinking most of the day.

My Uncle was what you would call a drunk back then, now we call these people alcoholics. Well any way I think you are starting to get a picture of my mothers life up to this point. It is probably safe to assume that this isn't the ideal life for a young woman.

The next event to happen in my moms life was for my uncle to fall in the shower one night after tying one on that night. He died soon after but my aunt seemed to make a another good choice and ended up marring the owner of the bar that they spent most of their time in.
The Grand essentials of happiness are: something to do, something to love, and something to hope for. Allan K. Chalmers

By this time my mom was in High School and met my future father. It wasn't exactly a marriage made in heaven. My dad was always an easy going man. He seemed to let most stuff go in one ear and out the other.

As you guessed it they had a few children. Nice one Dad and Mom. According to the books I have read on Angelic beings. People that believe in the after life and angels. They tell me I had a choice and was able to choose my parents....... What was I thinking...... I should have choose someone with some money and a couple of parents that were deeply in love .

How did I end up here in this situation.

I ended up loving my parents like most of us. They seemed to be doing the best that they could possibly do raising me, my bother and my sister. My mom and dad ended up getting a divorce and I went to live with my father.

My Father is remarried to a wonderful woman that seems to bring him a lot of happiness.
I haven't seen my mother for a while now. She lives with a life of excuses and misery. Her childhood was not the greatest but that doesn't give her the right to bring misery into other peoples lives. She has made a conscious choice to live what seems to be a painful life. Maybe her choices in life have made me choose happiness over misery.

I have always wondered what it is that motivates someone to live a life of true unhappiness when it takes the same amount of energy to live a life of joy. Life is meant to be full of joy and happiness so start today by making the right choices to live a fulfilling life of happiness.

If you are reading this and can't make up your mind what kind of life you truly want to live visit me at http://live.spiritualideas.com/ . Change your thinking and change your life.

Greg Vanden Berge will help you create a new approach to life and discover talents you never knew you had. We can help you get the most out of yourself all the time. Start developing your innate strengths and abilities to start enriching your life TODAY !

Changing Bad Habits

Sunday, June 7, 2009

Country Kitchen Designs

Kitchens figure amongst the important rooms of the entire house. Recently, a lot of attention is being paid to their presentation and decoration. This is because the concept of a kitchen being just an interior-cooking place has undergone transformation. Today, kitchens attract architects to provide them with the challenge of designing and decorating each kitchen uniquely. The designs of a kitchen can be done in numerous ways depending upon the desired style, preferable location, available area, and specific budget. The basic elements of the kitchen are to attribute the right kind of items to their appropriate places.

A country kitchen differs from a regular kitchen on the grounds of its plumbing fixtures, ventilations, dishwashers, flooring, and refrigeration. The peculiarity of country kitchens is that all its cabinets and counters are made of wood to give an authentic atmosphere. Two types of wood are used to make the furniture, namely Cedar wood and Oak wood. Another specialty about these kitchens is their in-house plant life and window dressing styles. Flowers such as daises and posies provide freshness to the kitchen. The window-dressing, if done in bright colors such as in red, yellow, or blue, illuminates the entire surrounding.

The country kitchen tables are traditionally round or oval, having matching wooden chairs that can be cushioned with pillows to complement the window dressings. The color combination of the furniture, window dressing, and other modern appliances should be harmonious. To give the kitchen a touch of inimitable charm, accessories such as old model car candleholders, old aluminum serving trays, wooden clocks, and variety of mug collections can be used. To make the bona fide atmosphere complete, country kitchen floors can be made of hardwood floor paneling for the required rustic look.

Country Kitchens can be designed according to the needs of the family members and their tastes. Sometimes professionals are hired to provide expertise on the designing and setting of the entire kitchen.

Kitchen Designs provides detailed information on Kitchen Design, Kitchen Cabinet Design, Kitchen Design Ideas, Kitchen Design Software and more. Kitchen Designs is affiliated with Small Kitchen Remodeling Ideas.

3 X 6 Mudsill For Shear Wall

Bathroom Vanity Ideas

Considering remodeling a bathroom? Just because it's in the bathroom doesn't mean it can't be as immaculately designed and cared for as the rest of the house. Here are some bathroom design ideas using different kinds of bathroom vanities.

The Antique Vanity

If the rest of the home is decorated in an antique style, make the bathroom match by adding an antique-style vanity. The bathroom sink can be set inside an antique-style wood setting, with elaborately finished wood designs, classic cabinet knobs, and heavy marble or granite tops and sink basins. Above the sink, hang an antique mirror of a size and shape that matches both the overall bathroom but also the look and color of the wood encasing the bathroom sink.

The Modern Vanity

On the opposite end of the spectrum from the antique vanity is the modern vanity. These vanities have sleek, stark, modern lines and materials. One popular new trend is to raise the bowl of the bathroom sink out of its usual recessed setting, so that it sits atop the bathroom counter. Mirrors for these bathroom vanities tend to be austere, no-nonsense rectangles which are nearly Zen-like in their simplicity. Some of these modern-style vanities do not have standard cabinets beneath the bathroom sink; instead, they appear more like a coffee table or stool with a bathroom sink inside - a very unique look for someone who wishes to make his or her bathroom strikingly different from the norm.

The Glass Vanity

Give the bathroom an even lighter, even more contemporary feeling by opting for a glass countertop and sink basin. Like some of the other modern vanities, the transparent glass sink basin is usually raised above its usual recessed position and sits atop the counter, like a beautiful giant glass serving bowl waiting for its occupants. The countertop itself can also be glass, giving the whole bathroom a light and airy feel. Underneath the glass countertop, install a standard, wooden bathroom cabinet so that bathroom "unsightlies", such as razors, toothbrushes, toothpaste, clippers, styling products, and so forth, still remain out of sight.

The choice of bathroom vanity should ultimately match one's personal style, and should fit with the overall design motifs of the home. Have fun designing a new bathroom vanity!

Mark Stein is a retired builder from Texas who is now a consultant for PMA Partners. Discount Bathroom Vanities

Wall Intersection With 4 X 6